I stand on the precipice!
Moderator: Moderators
- MoonBeemer
- Basic User
- Posts: 51
- Joined: Sun Sep 12, 2010 1:37 pm
I stand on the precipice!
The tools are procured. The knowledge perhaps acquired(I have read and reread Valve Adjustment for Dummies until I can quote it.). The R1150R quivers at the thought. At dawn tomorrow, I will take wrench in hand.
2004 R1150R
-
boxermania
- Quadruple Lifer
- Posts: 3644
- Joined: Thu Mar 17, 2005 6:37 pm
- Location: Baton Rouge, LA.....aproaching retirement
Re: I stand on the precipice!
Welcome, you might want to check the General FAQ discussion on this site and look for the Basic Maintenance Videos it might give you another perspective.
Good luck
Good luck
Member #312
06 Suzuki Burgman 650 "state of flux"
79 CBX
06 Suzuki Burgman 650 "state of flux"
79 CBX
Re: I stand on the precipice!
MoonBeemer,
I bet that you foud it a lot simpler to accomplish than it is to think about. I hope it went well.
I bet that you foud it a lot simpler to accomplish than it is to think about. I hope it went well.
Re: I stand on the precipice!
goodonyamate!
lettucenohowyawent
lettucenohowyawent
60% of the art of conversation is knowing when to say nothing
Re: I stand on the precipice!
Good luck....I still have not attempted that. Kinda want someone to hold my hand the first time around. It probably is easier than I would expect. Everything else on this bike has been. 
Buckster '03R
#543
#543
Re: I stand on the precipice!
Enjoy the fall. 
2017 Husqvarna 701
2007 Husqvarna TE250
2004 BMW Rockster
2007 Husqvarna TE250
2004 BMW Rockster
Re: I stand on the precipice!
Moonbeemer...
You are me, I am you... If I could do it, so can you (hey, that wasn't meant to rhyme!)... seriously, follow those steps, you can't go wrong. It's alot easier that you think, and extremely satisfying! Sometimes, I think I now enjoy working on my bike as much, if not more, that actually riding it!
You are me, I am you... If I could do it, so can you (hey, that wasn't meant to rhyme!)... seriously, follow those steps, you can't go wrong. It's alot easier that you think, and extremely satisfying! Sometimes, I think I now enjoy working on my bike as much, if not more, that actually riding it!
- MoonBeemer
- Basic User
- Posts: 51
- Joined: Sun Sep 12, 2010 1:37 pm
Re: I stand on the precipice! - Update!
Job Done! The machine has 900 miles on the 12000 mile service from a BMW dealership. Only the intake valves on the starboard side were anywhere within specs! She was running like a limping dog. I took my time and worked hard to make the intakes and exhaust valves as close to the same as possible to each other. What a difference, this has made in the way Moon runs. I estimate I have 40 percent more power. It is easy to tell she is aspirating far better. Also the spark plug cap removal tool I bought from Mark Parnes, really made removing the spark plug cap easy. All in all a fun, satisfying project. Next, is the TB sync. I have the TwinMax and check them today. They need it. Not real bad but, a little out. Thanks for the support. I was really suprised how much better she runs. The exhausts on the the port side were really too tight. Could have caused some damage if left for another 5000 miles. Keep your shinny side up. Roger
2004 R1150R
Re: I stand on the precipice!
Thanks for sharing your trepidation and elation with us.
60% of the art of conversation is knowing when to say nothing

